Pipes and Cisterns: formulas, shortcuts & solved examples
What it is
Pipes and cisterns is a version of time and work. Inlet pipes fill a tank, and outlets or leaks empty it. Each pipe's rate is counted as positive if it fills the tank and negative if it empties it, and the net rate tells you how long the tank takes to fill or empty.
Key formulas and rules
- If a pipe fills a tank in n hours, it fills 1/n of the tank each hour.
- If a pipe empties a full tank in m hours, its rate is −1/m of the tank per hour.
- Two inlets together: time taken = ab / (a + b).
- An inlet (a hours) and an outlet (b hours, with b > a): time to fill = ab / (b − a).
- Leak: a pipe normally fills the tank in a hours, but takes b hours because of a leak. The leak alone empties the full tank in ab / (b − a) hours.
- Net work done = sum of (rate × time) for each pipe, and the full tank counts as 1.
Sign convention
Inlets add to the tank and outlets subtract from it. If the net rate is negative, the tank is emptying, not filling.
Shortcuts
Shortcut 1: The LCM method
Assume the tank's capacity is the LCM of all the times given. Each pipe's rate then becomes a whole number of units per hour. This avoids fractions and speeds up the arithmetic.
Shortcut 2: Split into phases
When pipes are opened or closed at different times, work out how much each phase fills and subtract it from the whole tank. Then find how long the remaining pipes take to fill what is left.
Shortcut 3: Sense-check the time
Two inlets working together must take less time than the faster one alone. An inlet working against an outlet must take longer than the inlet alone. Use this to rule out answer options straight away.
Solved examples
Example 1
Pipe A fills a tank in 12 hours and pipe B fills it in 18 hours. How long will they take if both are opened together?
Combined rate = 1/12 + 1/18 = 3/36 + 2/36 = 5/36 of the tank per hour Time = 36/5 = 7.2 hours = 7 hours 12 minutes
With the LCM method, take the capacity as 36 units. A fills 3 units per hour and B fills 2, so together they fill 5 units per hour. 36 / 5 = 7.2 hours.
Example 2
A water tank on a housing society roof is filled by an inlet in 10 hours. An outlet can empty the full tank in 15 hours. If both are open, how long will the empty tank take to fill?
Net rate = 1/10 − 1/15 = 3/30 − 2/30 = 1/30 of the tank per hour Time = 30 hours
Check with the formula: (10 × 15) / (15 − 10) = 150 / 5 = 30 hours.
Example 3
Pipes A and B can fill a tank in 20 minutes and 30 minutes respectively. Both are opened together, but A is closed after 6 minutes. How long does it take in total to fill the tank?
In 6 minutes, both pipes fill 6 × (1/20 + 1/30) = 6 × 5/60 = 1/2 of the tank. The remaining 1/2 is filled by B alone in (1/2) × 30 = 15 minutes. Total time = 6 + 15 = 21 minutes.
Example 4
A pipe usually fills a tank in 8 hours. Because of a leak at the bottom, it now takes 10 hours. How long would the leak take to empty the full tank on its own?
Leak rate = 1/8 − 1/10 = 5/40 − 4/40 = 1/40 of the tank per hour The leak alone empties the tank in 40 hours.
Check with the formula: (8 × 10) / (10 − 8) = 80 / 2 = 40 hours.
Common mistakes
- Adding times instead of rates. Two pipes taking 12 hours and 18 hours don't take 30 hours together. Always add the rates (1/12 + 1/18), never the times.
- Getting the outlet's sign wrong. Treating an outlet as an inlet produces a time that is far too short. Mark each pipe with + or − before you combine them.
- Ignoring the phases. If a pipe is closed partway through, it contributes only for the time it was open. Work out each phase separately.
- Forgetting to take the reciprocal. A combined rate of 5/36 means 36/5 hours, not 5/36 hours. Flip the rate to get the time.
- Mixing units. If some times are given in hours and others in minutes, convert them all to one unit before you calculate any rates.
Practice now: https://www.testsworld.com/mocks